Free Shipping for all online orders over $100! Applies only to continental U.S.A.

z Account

VAC Statement Tube Phonostage

Have questions about this product?

We love answering questions. Talk to an expert now.

FREE SHIPPING

on all e-commerce orders over $100

TECH SUPPORT

Always Included

This VAC Statement dual mono triode vacuum tube phono (MM/MC, three gain modes, adjustable load, stereo/mono operation) preamplifier is designed for extreme applications. On the back panel there are two DC umbilical cords and large Amphenol aerospace connectors, a reminder of the massive dual mono power supply. There are inputs for four independent phone sources. In addition, each input may be of the conventional single-ended type or may be fully balanced.

Mechanical Design

The chassis is machined at VAC from high-grade, non-ferrous aluminum and processed through a series of plating steps. The resulting AICuNiCr chassis possesses superior RF rejection properties across a wide range of radio frequencies for greater resolution and subjectively blacker backgrounds. Similar care is taken around each of the six wideband audio transformers in each unit. In addition to the five regular line inputs, three of which may be used with balanced sources, there is also a fixed volume input for use as a slave in a multichannel home theater system, or with other sources that control their own level. The “cinema” source may also be balanced or single ended.

Electrical Design

The audio chassis is designed with distinct isolated sections dedicated to certain signal functions to prevent unwanted interactions among the circuits. Interconnecting wires are carefully routed and directed by spaced machined nonmetallic guides. The hand-wired vacuum tube audio circuit assemblies are bonded to massive brass loading plates, which in turn are isolation mounted to the main chassis for a very effective filter at audio frequencies. The avoidance of negative feedback and inclusion of input and output transformers confers the relatively unique trait of eliminating unwanted stray interactions between the source components and power amplifier, such as long chain interactions between their feedback loops which tend to coarsen the sound and flatten the sound stage.

Power Supply

A massive separate power supply is a dual mono design with substantial energy storage and high inherent regulation. Both resistive and inductive elements are used in concert with high-speed capacitor assemblies for the high voltage supplies, while active voltage stabilization is included in the four heater supplies and the 12-volt trigger supply.

Volume Control

The volume control is a massive one-pound multisection potentiometer some two inches long and nearly two inches in diameter, with machined brass shielding between the sections and against the outside world. This extraordinary part is critical in obtaining the highest fidelity in the world. A custom engineered VAC motor drive system allows the volume to be adjusted by remote control.  

Specification

Tubes

6x 12AX7

2 x E88CC/6922, ECC88/6DJ8, or 7308

Gain

352 dB MM (low gain)

70 dB MC (medium gain)

76 dB MC (high gain)

Up to 6 dB greater gain available on special order

Frequency Response

RIAA standard +/- 0.2 dB (20 Hz - 20 kHz)

-3 dB bandwidth 10 Hz - 80 kHz

Channel Separation

> 84 dB @ 1 kHz

Maximum Input

> 130 mV @ 1 kHz, MM (low gain); >500 mV @ 10 kHz

> 16 mV @ 1 kHz, MC (medium gain)/p>

> 8 mV @ 1 kHz, MC (high gain)/p>

Load Impedance

MM, 47k Ohms

MC (medium gain), selectable 400, 300, 200, 150, 100, or 50 Ohms

MC (high gain), selectable 100, 75, 50, 38, 25, or 13 Ohms

Load Capacitance

MM, 1, 100, 120, 150, 180, or 220 pF

Residual Noise

Less than 3MV at output (s/n ratio > 74 dB)

Absolute Phase

Does not invert absolute phase

Maximum Output

> 8 V RMS

Output Impedance

< 150 ohms, 20 Hz - 20 kHz, static (i.e., not dependent upon feedback)

Recommended Output Load

> 300 ohms

Power

External power supply, dual detachable umbilical cable (dual mono design), detachable IEC power cord

Voltage

May be ordered for 100v, 120v, 220v, or 230/240v operation

Illumination

Illuminated logo may be switched to bright, dim, of off.

Finish

Hand-rubbed gold-flake gloss black lacquer with chrome knobs standard.

Hand-rubbed metallic gloss silver lacquer with chrome knobs special order with additional cost.

Warranty

Two years parts and labor, excluding tubes (USA, see manual for full details)

Dimensions (H x W x D)

Audio chassis (not including knobs and connectors): 7 x 17.7 x 16.15 in.

Power supply (not including connectors): 5.8 x 17.7 x 16.15 in.

Shipping Weight

Phono stage chassis 56 lbs.

Power supply 64 lbs


Search

z